KNOWING PLUMBING BASICS IS IMPORTANT FOR INSTALLING A BATHTUB

Knowing Plumbing Basics is Important For Installing a Bathtub

Knowing Plumbing Basics is Important For Installing a Bathtub

Blog Article

Book

Have you been trying to find facts around Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Installing a tub isn't precisely rocket science, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably tough project. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall to eliminate the old bathtub and place the brand-new tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to leave the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the task and also fit trying it. Rather than working with a professional to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may require an expert plumber to make tube connections.
This short article will help you mount a new bath tub in your shower room if you have currently acquired a brand-new bathtub and do not require to change the setup of your previous supply of water pipes.
Your tools and also material checklist must comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installment


    To start with, the sustaining frame provided with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent pressure on the tub.
    Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final position.

    Removing Old Taps


    If you require to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted accessibility that is typically the instance.
    Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
    Prior to moving on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little factors.
    The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bathtub until the spirit level reads level.
    To set up taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression sign up with; then do the very same for the various other tap.
    Switch on the supply of water as well as examine all joints as well as new pipework for leaks as well as tighten them if essential. Fill up the bath tub and additionally check the overflow outlet and also the normal electrical outlet for leaks.
    Finally, take care of the bathroom paneling as described in the supplier's user's manual. Tiling as well as securing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it into its last placement.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Tub


    In the area where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can split fairly very early if you do not consider this activity prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water-proof glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    Hopefully you enjoyed our topic about How to Install a Bathtub Yourself. Thanks so much for spending some time to read through our piece. Kindly take the time to promote this write-up if you enjoyed reading it. Thanks a lot for your time. Please check our site back soon.


    Opt for our expert plumbers.

    Report this page